\n%:~\/Desktop\/CNC2418\/Restore firmware$ cu -s 115200 -l \/dev\/ttyUSB1
\nConnected.<\/p>\nGrbl 0.9j ['$' for help]
\n$$ (view Grbl settings)
\n$# (view # parameters)
\n$G (view parser state)
\n$I (view build info)
\n$N (view startup blocks)
\n$x=value (save Grbl setting)
\n$Nx=line (save startup block)
\n$C (check gcode mode)
\n$X (kill alarm lock)
\n$H (run homing cycle)
\n~ (cycle start)
\n! (feed hold)
\n? (current status)
\nctrl-x (reset Grbl)
\nok
\n$0=10 (step pulse, usec)
\n$1=25 (step idle delay, msec)
\n$2=0 (step port invert mask:00000000)
\n$3=5 (dir port invert mask:00000101)
\n$4=0 (step enable invert, bool)
\n$5=0 (limit pins invert, bool)
\n$6=0 (probe pin invert, bool)
\n$10=3 (status report mask:00000011)
\n$11=0.010 (junction deviation, mm)
\n$12=0.002 (arc tolerance, mm)
\n$13=0 (report inches, bool)
\n$20=0 (soft limits, bool)
\n$21=0 (hard limits, bool)
\n$22=0 (homing cycle, bool)
\n$23=0 (homing dir invert mask:00000000)
\n$24=25.000 (homing feed, mm\/min)
\n$25=500.000 (homing seek, mm\/min)
\n$26=250 (homing debounce, msec)
\n$27=1.000 (homing pull-off, mm)
\n$100=800.000 (x, step\/mm)
\n$101=800.000 (y, step\/mm)
\n$102=800.000 (z, step\/mm)
\n$110=5000.000 (x max rate, mm\/min)
\n$111=5000.000 (y max rate, mm\/min)
\n$112=800.000 (z max rate, mm\/min)
\n$120=10.000 (x accel, mm\/sec^2)
\n$121=10.000 (y accel, mm\/sec^2)
\n$122=10.000 (z accel, mm\/sec^2)
\n$130=200.000 (x max travel, mm)
\n$131=200.000 (y max travel, mm)
\n$132=200.000 (z max travel, mm)
\nok
\n<\/code><\/p>\n
\navrdude \u3067 grbl \u3092\u713c\u304d\u8fbc\u3080<\/h3>\n
avrdude\u306etarball\u3092\u843d\u3068\u3057\u3066\u304d\u3066\u3044\u304f\u3064\u304b\u8a66\u3057\u3066\u307f\u305f\u306e\u3067\u3059\u304c\uff0c
\n\u4f55\u304b\u30bf\u30a4\u30df\u30f3\u30b0\u306e\u554f\u984c\u306a\u306e\u304b\u3044\u305a\u308c\u3082\u4e0a\u624b\u304f\u57fa\u677f\u3068\u901a\u4fe1\u3067\u304d\u307e\u305b\u3093\u3067\u3057\u305f\u3002<\/p>\n
\u305d\u3053\u3067\uff0c\u30ad\u30c3\u30c8\u306b\u4ed8\u5c5e\u3057\u3066\u3044\u305f avrdude.exe \u3092wine\u304b\u3089\u4f7f\u3063\u3066grbl\u3092\u713c\u304d\u8fbc\u307f\u307e\u3059\u3002<\/p>\n
\u3061\u306a\u307f\u306b\uff0c\u3053\u306e\u30ad\u30c3\u30c8\u4ed8\u5c5e\u306eavrdude.exe\u306f v5.4\u3067\u3057\u305f\u3002<\/p>\n
wine\u3067COM\u30dd\u30fc\u30c8\u3092\/dev\/ttyUSBx \u306b\u30de\u30c3\u30d7\u3059\u308b\u306b\u306f\uff0c~\/.wine\/dosdevices \u306b \/dev\/ttyUSBx \u306e\u30b7\u30f3\u30dc\u30ea\u30c3\u30af\u30ea\u30f3\u30af\u3092\u5f35\u3063\u3066\u3042\u3052\u307e\u3059\u3002<\/p>\n
\n%:~\/.wine\/dosdevices$ ls -al
\ntotal 0
\nlrwxrwxrwx 1 xxx xxx 10 Jan 29 2017 c: -> ..\/drive_c
\nlrwxrwxrwx 1 xxx xxx 12 Jan 29 2017 com1 -> \/dev\/ttyUSB0
\nlrwxrwxrwx 1 xxx xxx 12 Jan 27 12:49 com2 -> \/dev\/ttyUSB1
\nlrwxrwxrwx 1 xxx xxx 12 Jan 27 12:49 com3 -> \/dev\/ttyUSB2
\nlrwxrwxrwx 1 xxx xxx 8 Jan 29 2017 d:: -> \/dev\/sdc
\nlrwxrwxrwx 1 xxx xxx 27 Jan 29 2017 e: -> \/media\/evilmaster\/1C65-1D01
\nlrwxrwxrwx 1 xxx xxx 9 Jan 29 2017 e:: -> \/dev\/sdc1
\nlrwxrwxrwx 1 xxx xxx 8 May 8 2017 f:: -> \/dev\/sr0
\nlrwxrwxrwx 1 xxx xxx 1 Jan 29 2017 z: -> \/
\n<\/code><\/p>\nWine\u7d4c\u7531\u3067avrdude\u3092\u8d77\u52d5\u3057\uff0c\u30dc\u30fc\u30c9\u306egrbl\u3092\u713c\u304d\u8fbc\u307f\u307e\u3059\u3002
\n\u3053\u306e\u3068\u304d\uff0cCOM\u30dd\u30fc\u30c8\u306f\u4e0a\u306e\u30ea\u30f3\u30dc\u30ea\u30c3\u30af\u30ea\u30f3\u30af\u306e\u540d\u524d\u3092\u6307\u5b9a\u3057\u307e\u3059\u3002<\/p>\n
\n%:~\/Desktop\/CNC2418\/Restore firmware$ wine avrdude.exe -p m328p -c stk500 -b 115200 -P COM2 -U flash:w:grbl_v1.1f.20170801.hex
\nFontconfig warning: \"\/etc\/fonts\/conf.d\/69-language-selector-ja-jp.conf\", line 126: Having multiple values in isn't supported and may not work as expected
\nFontconfig warning: \"\/etc\/fonts\/conf.d\/69-language-selector-ja-jp.conf\", line 126: Having multiple values in isn't supported and may not work as expected
\nFontconfig warning: \"\/etc\/fonts\/conf.d\/69-language-selector-ja-jp.conf\", line 126: Having multiple values in isn't supported and may not work as expected
\nFontconfig warning: \"\/etc\/fonts\/conf.d\/69-language-selector-ja-jp.conf\", line 126: Having multiple values in isn't supported and may not work as expected
\nFontconfig warning: \"\/etc\/fonts\/conf.d\/69-language-selector-ja-jp.conf\", line 126: Having multiple values in isn't supported and may not work as expected
\navrdude.exe: successfully opened stk500v1 device -- please use -c stk500v1<\/p>\navrdude.exe: AVR device initialized and ready to accept instructions<\/p>\n
Reading | ################################################## | 100% 0.00s<\/p>\n
avrdude.exe: Device signature = 0x1e950f
\navrdude.exe: NOTE: FLASH memory has been specified, an erase cycle will be performed
\n To disable this feature, specify the -D option.
\navrdude.exe: erasing chip
\navrdude.exe: reading input file \"grbl_v1.1f.20170801.hex\"
\navrdude.exe: input file grbl_v1.1f.20170801.hex auto detected as Intel Hex
\navrdude.exe: writing flash (30492 bytes):<\/p>\n
Writing | ################################################## | 100% 4.97s<\/p>\n
avrdude.exe: 30492 bytes of flash written
\navrdude.exe: verifying flash memory against grbl_v1.1f.20170801.hex:
\navrdude.exe: load data flash data from input file grbl_v1.1f.20170801.hex:
\navrdude.exe: input file grbl_v1.1f.20170801.hex auto detected as Intel Hex
\navrdude.exe: input file grbl_v1.1f.20170801.hex contains 30492 bytes
\navrdude.exe: reading on-chip flash data:<\/p>\n
Reading | ################################################## | 100% 3.87s<\/p>\n
avrdude.exe: verifying ...
\navrdude.exe: 30492 bytes of flash verified<\/p>\n
avrdude.exe: safemode: Fuses OK<\/p>\n
avrdude.exe done. Thank you.
\n<\/code><\/p>\n
\u3069\u3046\u3084\u3089\uff0cWindows\u7248\u306eavrdude\u306f\u4e0a\u624b\u304f\u66f8\u304d\u8fbc\u3081\u308b\u3088\u3046\u3067\u3059\u3002<\/p>\n
\u66f8\u304d\u8fbc\u3093\u3060\u3089\u5148\u7a0b\u3068\u540c\u3058\u3088\u3046\u306bcu\u7b49\u3067grbl\u306b\u30a2\u30af\u30bb\u30b9\u3059\u308b\u3068\uff0cversion\u304c\u4e0a\u304c\u3063\u3066\u3044\u308b\u306e\u3092\u78ba\u8a8d\u3067\u304d\u307e\u3059\u3002<\/p>\n
\n%:~\/Desktop\/CNC2418\/Restore firmware$ cu -s 115200 -l \/dev\/ttyUSB1
\nConnected.<\/p>\nGrbl 1.1f ['$' for help]
\n[HLP:$$ $# $G $I $N $x=val $Nx=line $J=line $SLP $C $X $H ~ ! ? ctrl-x]
\nok
\n$0=10
\n$1=25
\n$2=0
\n$3=0
\n$4=0
\n$5=0
\n$6=0
\n$10=1
\n$11=0.010
\n$12=0.002
\n$13=0
\n$20=0
\n$21=0
\n$22=0
\n$23=0
\n$24=25.000
\n$25=500.000
\n$26=250
\n$27=1.000
\n$30=1000
\n$31=0
\n$32=0
\n$100=250.000
\n$101=250.000
\n$102=250.000
\n$110=500.000
\n$111=500.000
\n$112=500.000
\n$120=10.000
\n$121=10.000
\n$122=10.000
\n$130=200.000
\n$131=200.000
\n$132=200.000
\nok
\n<\/code><\/p>\n
\u3042\u3068\u306f\uff0c\u30d1\u30e9\u30e1\u30fc\u30bf\u3092\u5148\u7a0b\u30e1\u30e2\u3063\u3066\u3044\u305f\u5024\u306b\u76f4\u305b\u3070\uff0cgrbl\u306e\u30a2\u30c3\u30d7\u30b0\u30ec\u30fc\u30c9\u306f\u5b8c\u4e86\u3068\u306a\u308a\u307e\u3059\u3002<\/p>\n
\n\u3042\u3068\u304c\u304d<\/h2>\n
Linux\u7248\u306eavrdude\u304b\u3089\u4f55\u6545\u304b\u66f8\u304d\u8fbc\u3081\u306a\u3044\u306e\u3067\uff0c\u30ad\u30c3\u30c8\u4ed8\u5c5e\u306eavrdude\u304c\u7279\u6b8a\u306a\u3093\u3067\u3059\u304b\u306d\uff1f
\n\u3061\u3087\u3063\u3068\u91c8\u7136\u3068\u3057\u307e\u305b\u3093\u304c\uff0cgrbl1.1\u306b\u7c21\u5358\u306b\u4e0a\u3052\u308b\u3053\u3068\u306f\u3067\u304d\u305f\u306e\u3067\u826f\u3057\u3068\u3057\u307e\u3059\u3002\u3002<\/p>\n","protected":false},"excerpt":{"rendered":"
\u3068\u3046\u3068\u3046\u4e2d\u83efCNC\u5c0e\u5165\u3057\u305f\u306e\u3067\uff0c\u305d\u306e\u30d5\u30a1\u30fc\u30e0\u4e0a\u3052\u3092\u3057\u305f\u306e\u3067\u4f5c\u696d\u30e1\u30e2\u3092\u6b8b\u3057\u3066\u304a\u304d\u307e\u3059\u3002<\/p>\n","protected":false},"author":1,"featured_media":513,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"colormag_page_container_layout":"default_layout","colormag_page_sidebar_layout":"default_layout","jetpack_post_was_ever_published":false,"_jetpack_newsletter_access":"","_jetpack_dont_email_post_to_subs":false,"_jetpack_newsletter_tier_id":0,"_jetpack_memberships_contains_paywalled_content":false,"_jetpack_memberships_contains_paid_content":false,"footnotes":"","jetpack_publicize_message":"","jetpack_publicize_feature_enabled":true,"jetpack_social_post_already_shared":true,"jetpack_social_options":{"image_generator_settings":{"template":"highway","default_image_id":0,"font":"","enabled":false},"version":2}},"categories":[13,10],"tags":[],"class_list":["post-508","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-electronics","category-gadget"],"jetpack_publicize_connections":[],"jetpack_featured_media_url":"https:\/\/i0.wp.com\/nyacom.net\/wp-content\/uploads\/2018\/01\/IMG_20180121_153006.jpg?fit=1536%2C2048&ssl=1","jetpack_sharing_enabled":true,"jetpack_shortlink":"https:\/\/wp.me\/p6V68f-8c","jetpack-related-posts":[],"_links":{"self":[{"href":"https:\/\/nyacom.net\/index.php?rest_route=\/wp\/v2\/posts\/508","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/nyacom.net\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/nyacom.net\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/nyacom.net\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/nyacom.net\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=508"}],"version-history":[{"count":4,"href":"https:\/\/nyacom.net\/index.php?rest_route=\/wp\/v2\/posts\/508\/revisions"}],"predecessor-version":[{"id":515,"href":"https:\/\/nyacom.net\/index.php?rest_route=\/wp\/v2\/posts\/508\/revisions\/515"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/nyacom.net\/index.php?rest_route=\/wp\/v2\/media\/513"}],"wp:attachment":[{"href":"https:\/\/nyacom.net\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=508"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/nyacom.net\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=508"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/nyacom.net\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=508"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}
![\"\"](\"https:\/\/i0.wp.com\/nyacom.net\/wp-content\/uploads\/2018\/01\/IMG_20180121_115928.jpg\")
<\/a><\/p>\n